Roof Slope Calculator

CARPENTRY - HOUSING BASIC ROOF And CEILING FRAMING - Wikispaces
CARPENTRY - HOUSING ©TAFE NSW Construction and Transport Division 3 THE ROOF The roof, and roof covering, makes up a large part of the external fabric of the building. ... Retrieve Doc

SIZING DATA (For Conventional Drainage)
ROOF DRAIN VERTICAL REQUIREMENT FOR HORIZONTAL ROOF AREAS AT VARIOUS RAINFALL RATES* When sizing roof drains, the limiting factor for the amount of water each drain will carry away is the size of leader.Therefore, increasing ... Doc Viewer

Types Of Roof Drains, And How To Size Them - About.com Money
Roof drains come in different shapes, sizes, and will vary on the roof and building where they will be installed. Before deciding which roof drain to use, consider the roof size, pitch, drain location, inflow rate, safety requirements and rainfall volume. ... Read Article

APPENDIX A ROOF DRAIN SIZING METHOD - ECodes
APPENDIX A ROOF DRAIN SIZING METHOD (APPENDIX A IS FOR INFORMATIONAL PURPOSES ONLY) A101 Sizing Example The following example gives one method of sizing the ... Read Document

The Dope On slope - RCI, Inc.
Roof-slope terminology, and has assembled calculator will provide the square root as . well as convert to feet, inches, and fractions. Length of slope is also important when . doing an estimate or plan takeoff, because . the quantity of material needed increases . ... Read More

Effect Of Solar Radiation Control On Electricity Demand Costs ...
Insolation), R-value of the low-slope roof, and solar reflectance and infrared emittance of the roof surface. Cool Roof Calculator with data from test roofs at the Oak Ridge National Laboratory . 4 (Wilkes, et al. 2000). ... Retrieve Document

Spreadsheet Calculator - A Roof Framing How-to
A Great Tool for the Roof Framer. Sheet3 Sheet2 Sheet1 Indicates: Roof Framing “Calculator Slope 6th Jack Common: 7th Jack Tan. corner 8th Jack Wall Length. Angle 9th Jack Hip Side 10th Jack Cut at 12th Jack Center Post: ... Visit Document

The Code Corner No. 6 - Roofing NF - RLGA Technical Services
Part of keeping moisture from entering the building is the slope of the roof to provide drainage. The minimum roof slope is 1/4 inch in 12 inches (2% slope). Missing in the ©2009 RLGA Technical Services LLC — www.specsandcodes.com No. 6 — Roofing — Page 2 ... Retrieve Content

Roof Pitch - Wikipedia, The Free Encyclopedia
In building construction, roof pitch is a numerical measure of the steepness of a roof. Roofs may be functionally flat or "pitched ... Read Article

Slope - Wikipedia, The Free Encyclopedia
In mathematics, the slope or gradient of a line is a number that describes both the direction and the steepness of the line. Slope is often denoted by the letter m. ... Read Article

PROPER GUTTER AND DOWNSPOUT SIZING - Gutter Supply Co
PROPER GUTTER AND DOWNSPOUT SIZING DESIGN OF ROOF DRAINAGE SYSTEMS ROOF DRAINAGE The roof is one of the most essential parts of a building as ... Return Document

ROOFSLOPE.COM 1-888-255-1888 ROOFSLOPE
ROOF SLOPE This product combines a proprietary blend of cementitious polymer emulsions and aggregates to achieve a workable, easy to use, sloping compound. ... Return Document

Installing Gutter Heat Tape - About.com Home
The installation of gutter heat tape to your roof can help prevent damages caused by ice dams. About.com. Food; Health; Home; Money; Style; Tech; Loop the heat tape up and down in a zigzag pattern starting from about 12 inches up the roof slope and then position to hang down over and beyond ... Read Article

How To Estimate Framing Material - Guide
How to Estimate Framing Material. Step by step on how to estimate framing material. About.com. Food; Health; Home; Let’s start framing the roof. To calculate the fascia, measure the length of each slope side, add double the overhang measurement on each end of the roof. 6. ... Read Article

Firestone Tapered Polyiso. Design Guide
1/2"ft. Slope Cross Sections 2.5".5" 6.5" 4.5" 3" 1" 7" 5" Published July 2006 Page 7 The material is Firestone ISO 95+ Tapered and Flat Polyisocyanurate Roof Insulation. ... Fetch Content

Roof Drainage - LYSAGHT®
Roof drainage systems can be affected by a number of variables and must Calculate the catchment area of the roof from the plan. To allow for the slope of the roof, increase the plan area by 1% for every degree of pitch up to 36°. ... Return Document

Report Of Roof System Design Wind-load Analysis
"Standard Guide for Low Slope insulated Roof Membrane Assembly Performance." Roof systems' wind-uplift capacities typically are determined by laboratory testing or engineering analysis. Roof Wind Calculator - SAMPLE TEST BUILDING ... Retrieve Doc

UNIT III: Finding Slope Of Tangent With TI Calculators
UNIT III: Finding Slope of Tangent With TI Calculators After performing the incline lab (unit III), the students obtain a graph whose equation is x = kt^2. The calculator draws a tangent line and gives you the value of dy/dx (on ... Get Content Here

The Importance Of Proper roof slope
Roof slope when reviewing plans before actual building construction. For reroofing operations, some building codes allow for performance-based measures of positive drainage for defining required minimum roof slope. For example, IBC’s Section 1510.1- ... Return Doc

Construction Master 5 Drop Or Slope Calculations How To
Http://www.calculated.com/cm5 See how the Construction Master 5 contractor calculator's built-in right triangle solution keys let you quickly and accurately calculate the drop or fall or slope of any lot, pad, roof or drain pipe. If it's got a slant to it you can calculate the rise or ... View Video

Metal slope Requirements - National Roofing Contractors ...
Mum slope recommendation for metal roof systems is prescriptive, whereas NRCA recommendations for low-slope membrane roof systems are performance-based. For example, NRCA recommends designers should not only specify that a low-slope membrane roof system ... Retrieve Content

Slope Factor Chart
1:12 1.0035 1.4167 Pitch of Roof Slope Factor Valley & Hip Factor 2:12 1.0138 1.4240 3:12 1.0308 1.4362 4:12 1.0541 1.4530 5:12 1.0833 1.4743 6:12 1.1180 1.5000 7:12 ... Fetch Full Source

roof calculation Tips - Nansulate
Add percentage for slope of roof. (for Fiberglass, Asphalt Shingle, Wood Shingle roofs. (column C) Step 4. Add percentage for flat tile roof (butt ends). (column D) Step 5. Add percentage for barrel tile roof. (column E) ... Get Content Here

Roof Plans - Patch Independent Home Inspections
FIGURE 20.6 In determining the roof slope, the angle is expressed as a comparison of equal units. Units may be inches, feet, meters, etc., as long as the horizontal and vertical units are of equal length. COMMON ANGLES FOR DRAWING ROOF PITCHES ROOF PITCH ANGLE ... Read Here

How To Determine The slope Of A roof - YouTube
Http://www.learningconstruction.com Step by Step Tutorial: This video will explain how to determine the slope on a roof. Slope is normally described by the ratio of the "rise" divided by the "run" between two points on a line. In construction, we will use the same numbers without ... View Video